Forcefield My Account  Cart Contents  Checkout  
  Top » Catalog » Renewable Energy » Wind Turbine Kits and Parts » 6642 My Account  |  Cart Contents  |  Checkout   
Books-> (37)
Magnets and Magnetism-> (124)
Needful Things (10)
Renewable Energy-> (51)
  RE Books (14)
  Wind Turbine Kits and Parts (37)
Rummage Sale (23)
What's New? more
Vertical Low RPM alternator
Vertical Low RPM alternator
Quick Find
Use keywords to find the product you are looking for.
Advanced Search
Magnet Safety
Magnet Facts
Magnet Types
Uses and Demos
Wind Power
48 Volt Stator

3 Phase Stator for Axial Flux Wind Turbine project

DUE TO A BACKLOG OF ORDERS, WE ARE NOT CURRENTLY ACCEPTING ORDERS FOR THIS ITEM. Please Email us for more information on when this alternator will be available again.

We offer this for those folks who want to build their own wind turbine but don't care to wind their coils or cast the stator, or for some perhaps this could serve as a replacement part.

This stator is wound with #16 gage wire. It has 9 coils and each coil has 130 turns in it. We use the same high grade 200 deg C magnet wire in these that we sell on the website. The coils are wired in 3 phase star configuration. They are cast in a mixture of vinyl ester and ATH (Aluminum trihydroxide)

The stator is 1/2 inch thick and 15.5 inches in diameter. The hole in the center is 5.75 inches in diameter. We do not drill out any holes for mounting but if youd like it drilled out to fit our stator bracket send us a note with your order and we'll do that. This stator fits machines that use magnets 2 inches tall (or diameter) fit to 12 inch diameter rotors. It's a perfect fit for the machines on our website at It would work well with the older brake disc designs (so long as the brake disks are 12 inches in diameter) or our more recent ideas featured here:

With some slight changes to the mounting brackets, this stator would also work well with the 10 foot diameter machine featured in Hugh Piggotts plans 'How to build a Wind Turbine'.

We offer several different stators here so be sure this is suits your needs best. If you have any questions feel free to email us before you order.

This particular stator is well suited for a 48 volt system. The magnet rotors should be 12 inches in diameter and each rotor should have 12 of the 1 inch by 2 inch by half inch blocks installed. After you rectify the output to direct current, this stator should produce 48 Volts at 140 rpm. The blades should be 10 foot in diameter.

Pictured above is the power curve for an alternator built with this stator. That alternator has an airgap of .68 inches (the airgap is the distance between magnet rotors), 12 inch rotors, and a total of 24 1 inch by 2 inch by half inch N40 NdFeB magnets.

In our tests we believe this stator will be about 50% efficient at 700 Watts. Sustained output above about 700 Watts may overheat this stator so you should design your machine to furl before that point.

We do not drill any mounting holes in the stator. We figure folks might want to drill it out to suit their own frame work. If you would like us to drill this out so it fits the stator bracket in our metal work kits (see other products) just send us a note with the order and well do it for you!

We make these stators in our shop, which is located in the mountains of Colorado off the power grid. We are totally powered by homebrew wind power. These stators are hand made and cast in fairly primitive wooden molds. Sometimes we get air bubbles in the casting. If they are real ugly we fill them, but otherwise they are just a cosmetic defect. So please dont expect cosmetic perfection - were working on it but were not there yet!

We make these to order. We may not be able to ship stators for 2 weeks after your order so please keep that in mind! (most of the time were faster)

DUE TO A BACKLOG OF ORDERS, WE ARE NOT CURRENTLY ACCEPTING ORDERS FOR THIS ITEM. Please Email us for more information on when this product will be available again.

This product was added to our catalog on Monday 26 February, 2007.
Jan 1st 2012 - Due to the acquisition of Forcefield by Amazing Magnets, we have temporarily disabled purchasing on the shopping cart. For immediate needs for magnets please visit For wind power products visit
Customers who bought this product also purchased
Thin Cyanoacrylate Glue, 2oz.
Thin Cyanoacrylate Glue, 2oz.
2 oz Accellerator for Cyanoacrylate glues
2 oz Accellerator for Cyanoacrylate glues
NdFeB Disc,  2 in. x  1/2 in.
NdFeB Disc, 2 in. x 1/2 in.
Thick Viscosity Cyanoacrylate Glue, 2oz.
Thick Viscosity Cyanoacrylate Glue, 2oz.
Stainless Steel 1/2 inch AN washer
Stainless Steel 1/2 inch AN washer
Stainless steel 1/2-13tpi NUT
Stainless steel 1/2-13tpi NUT
Related Products
Related Categories
Related Manufacturers
Shopping Cart more
0 items
Manufacturer Info
Other products
Notifications more
NotificationsNotify me of updates to 48 Volt Stator
Reviews more
Write ReviewWrite a review on this product!
Shipping & Returns
Privacy Notice
Conditions of Use
Contact Us

Linux Powered website! Our company does not use Microsoft products.
All content ©2005 by FORCEFIELD.
Best viewed with ANY browser! Our company does not use Microsoft products.

Copyright © 2003 osCommerce
Powered by osCommerce